FAAC Gate Installation Nationwide

FAAC Gate Installation in Orlando: What to Know First

FAAC gate installation in Orlando typically runs $2,200 to $6,800 for a complete residential system, depending on whether you’re putting in a slide or swing configuration, and most jobs are completed in one to two days once the equipment arrives. We’re an independent FAAC service provider, not a manufacturer-authorized shop, which means we’re free to recommend the fix or install that actually fits your property and budget instead of pushing whatever the factory manual says. If you own an FAAC gate and the install is failing, or you’re pricing out a new one, this page gives you real numbers and the specific things we see in Orlando’s climate.

Call (850) 816-3017

This page is for homeowners who already own FAAC equipment and need installation or replacement work. If you’ve got a gate that won’t open, a new build, or an operator that’s been patched too many times, call (850) 816-3017 and talk to a live person, day or night.

How FAAC Products Fail – and How We Fix Them

FAAC makes solid operators. We respect the engineering. But Orlando’s heat, daily afternoon rain, and sandy soil create failure patterns we can almost diagnose over the phone. Here’s what we run into most on FAAC installs across Orange County.

• FAAC 402 and 422 swing operators: capacitor burnout from afternoon heat. These are the workhorse swing operators in Orlando subdivisions like Baldwin Park and Dr. Phillips. The start capacitor sits inside the housing where direct sun drives internal temperatures past 140 degrees in July. Six or seven years of that, and the gate starts humming but won’t move. We replace the capacitor with a higher-temperature-rated part and relocate or shield the housing where the install allows.
• FAAC 844 slide operator: limit-switch drift on long driveways. The 844 is common on estate properties in Windermere and Winter Park where drives run 60 to 120 feet. The magnetic limit switches are sensitive to vibration, and over time the gate stops an inch or two short of fully closed. That gap is just big enough for a dog to slip through or a delivery person to squeeze in. We re-tune the limits, inspect the gate rollers for flat spots that amplify vibration, and set the stops with a physical backstop as backup.
• FAAC 750 hydraulic operator: fluid thinning in summer, sluggish in winter. The 750 series is a heavy-duty hydraulic swing operator we see on older estate gates and some commercial properties near International Drive. Hydraulic fluid degrades differently in Florida than it does in cooler climates. By August, thinned fluid makes the gate drift or bounce at the end of travel. We flush and refill with the viscosity grade matched to central Florida’s temperature swing, which extends pump life significantly.
• FAAC S418 slide operator: gear wear from sandy soil intrusion. The S418 shows up on a lot of newer installs. In Orlando, the issue is fine sugar sand working its way into the rack-and-pinion gear mesh. It acts like lapping compound, wearing the pinion teeth down until the gate shudders mid-travel. We clean the rack, replace the pinion if it’s worn past tolerance, and add a brush seal that keeps most of the grit out without binding.
• FAAC C720 low-voltage wiring: ant and moisture intrusion at the junction box. The C720 is a solid mid-range slide operator, but the low-voltage terminal strip is a magnet for moisture ants and humidity corrosion in Orlando’s wet summers. Symptoms are intermittent safety-edge faults or the gate reversing for no visible reason. We replace the strip, dielectric-grease the connections, and seal the conduit entry so moisture can’t wick up into the housing.

Our FAAC Gate Installation Process

Every FAAC install in Orlando follows the same sequence. No surprises, no add-ons at the door. Here’s how a job runs from first call to final walkthrough.

1. 1
   Call and describe what the gate is doing, or what you want built. A live person answers. Tell us what you’ve got, and we’ll give you a preliminary range before we ever schedule the truck.
2. 2
   On-site evaluation and written quote. We measure the gate, check the posts, test the existing operator if there is one, and put the complete price in writing. That number covers parts, labor, and cleanup. It doesn’t change unless you change the scope.
3. 3
   Parts decision, made together. For FAAC work, we use OEM parts when the warranty requires it or when the aftermarket equivalent doesn’t meet the torque and duty-cycle specs. For older out-of-warranty units, a quality aftermarket capacitor or limit switch can save real money. We show you the options and the prices.
4. 4
   Installation. Our technicians arrive in uniform, within the window we committed to. They do the mechanical work, the low-voltage wiring, and the safety-edge installation in one visit for most residential jobs.
5. 5
   Testing and safety verification. We cycle the gate under load, test the obstruction reversal, check photo-eye alignment, and run the gate in both directions at least a dozen times. FAAC operators have specific entrapment-protection requirements, and we set them to manufacturer spec.
6. 6
   The Kingswell Guarantee, in writing. Before we leave, you get a written guarantee stamped on the invoice. Every install carries the 365-Day Done Right Promise. If something fails inside that year, we come back and fix it at no charge. No call-center runaround, no pro-rated nonsense.

What FAAC Gate Installation Costs in Orlando

Straight numbers, because that’s what people actually want. Here’s what we quote for the common FAAC scenarios across Orlando:

• FAAC 402 or 422 swing operator replacement on an existing gate: $2,200 to $3,400 parts and labor. This assumes the gate, hinges, and posts are in sound condition and we’re swapping the operator, arms, and controls.
• FAAC 844 slide operator on an existing track system: $3,000 to $4,800 parts and labor. Includes rack repair where needed, limit setup, and safety-edge integration.
• Complete new FAAC slide gate install with operator, steel gate, and track: $4,500 to $6,800 for a typical single-family driveway in Orlando. Price moves based on gate weight, length of track, and whether we need to pour a new concrete pad for the operator.
• FAAC 750 hydraulic swing operator for a heavy estate gate: $3,800 to $5,600 parts and labor. Hydraulic work costs more because of the fluid flush, pump service, and valve adjustments.

What moves the price: gate size and weight, whether the existing posts are plumb and true, the condition of the track or hinges, and how far the power is from the operator location. We quote it all in writing before any work starts. Call (850) 816-3017 for an exact number on your specific property. The estimate is free.

Why Orlando Homeowners Call Portcullis Gate Repair Orlando for FAAC Work

We’ve been running gate jobs here since 2008. That’s long enough to have seen every FAAC model from the old 400 series through the current C720 line installed, abused, and resurrected. Dean Prescott founded this shop with one operating principle: tell the customer the price before you touch a thing, and stand behind the work in writing. That’s the Kingswell Way. Written price. Real arrival window. Clean job site. Written guarantee on every repair. Come back if it fails. Five commitments, on paper, every time.

We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which means if you’re running a mixed-brand property, one call covers everything. Our techs already know the FAAC-specific wiring, entrapment-protection settings, and torque curves before they pull into your driveway. And every repair carries the 365-Day Done Right Promise, written on the invoice. If it fails inside a year, we return and make it right at no charge. That’s not a marketing line. It’s the guarantee stamp.

FAQs