Ghost Controls Gate Installation Nationwide

Ghost Controls Gate Installation in Orlando: What to Know First

We install, repair, and replace Ghost Controls gate operators throughout Orlando, and most installations are completed in a single visit once parts are on the truck. The honest price posture is this: we give you a written number before any work starts, and that number does not change when the technician is standing in your driveway. If you are calling about a Ghost Controls system that is dead, sluggish, or only opens halfway, call (850) 816-3017 and tell us what the gate is doing, or not doing. We will give you a real dollar range before we touch a thing.

Call (850) 816-3017

This page is for Orlando homeowners who own a Ghost Controls opener, or are considering one, and want a technician who actually knows the brand’s quirks rather than a generalist who figures it out on your dime.

How Ghost Controls Products Fail, and How We Fix Them

Ghost Controls builds solid residential operators, but Orlando’s climate and daily use expose predictable weak points. Here are the five we see most often across the city:

• AXDP and AXD series arm actuator drifting out of sync. The linear arm on a Ghost Controls swing gate relies on internal limit settings to know where “open” and “closed” are. After enough cycles, or after a power blip during a storm, those limits drift. The gate stops short or over-travels and slams the post. We re-run the limit programming sequence and verify the arm’s travel with the gate attached, not on the bench. That last part matters more than people think.
• R20 and TSS1 control board corrosion from humidity. Orlando’s summer moisture works its way into control boxes that are not sealed well, and we regularly see green corrosion on the low-voltage terminals of the R20 board. The symptom is usually an opener that hums but will not move, or a keypad that lights up but does nothing. We clean the terminals, replace the board only when the traces are gone, and re-seal the enclosure with a proper gasket rather than letting it breathe the Florida air.
• Photo-eye alignment problems after concrete settles. Every Ghost Controls installation uses safety photo-eyes, and Orlando’s sandy soil plus afternoon downpours shift gate posts and the conduit stub-outs the eyes sit on. The eyes lose alignment and the gate refuses to close, or reverses mid-travel. We re-align and, where the post has moved enough to matter, we reset the stub-out so the eye stays put through the next rainy season.
• Arm actuator motor running but the gear stripped. This one sounds fine until you watch the arm. The motor spins, but the gate does not move, or it moves with a grinding sound. Ghost Controls arms use a plastic gear inside the actuator housing on several residential models, and after enough force against wind or a sagging gate, that gear strips. We replace the gear with either the OEM part or a proven aftermarket equivalent, and we tell you which one we are using and why before we order it.
• Ghost Controls keypad and remote receiver losing range after a year or two. We hear this a lot in Orlando neighborhoods with dense stucco walls and metal roofs. The receiver antenna inside the control box picks up interference, and remotes that worked from the street now only work from ten feet away. We relocate the antenna outside the metal enclosure, or install a remote receiver module, and range returns. It is a fifteen-minute fix that gets misdiagnosed as a bad remote all the time.

Our Ghost Controls Gate Installation Process

Here is how a Ghost Controls installation goes with us, from the first call to the final test:

1. 1
   You call, a person answers. We ask what the gate is doing and what Ghost Controls model you have. If you do not know the model, we walk you through finding the label on the arm or control board.
2. 2
   We diagnose before we quote. For a new installation, we measure the gate leaf, check the post condition, and confirm the power location. For a repair or replacement, we test the operator, the photo-eyes, the keypad, and the battery backup if you have one.
3. 3
   We give you the written price. You get a dollar range for parts and labor, in writing, before any bolt is turned. If we find something else once we start, we stop and call you with a new number before we keep going.
4. 4
   We do the work. That means mounting the actuator or operator, running the low-voltage wiring, setting the limits, aligning the photo-eyes, and programming your remotes and keypad.
5. 5
   We test it repeatedly. The gate cycles open and close several times, with a person standing at the photo-eyes to confirm the safety reversal works. We also check the manual release so you can open the gate during a power outage.
6. 6
   We hand you the written guarantee and clean up. Every Ghost Controls job carries the 365-Day Done Right Promise, stamped on the invoice. If the repair fails inside that year, we return and fix it at no charge. No call-back fee, no argument.

What Ghost Controls Gate Installation Costs in Orlando

You should know the numbers before you commit to anything. Here is what we typically see in the Orlando market:

• New Ghost Controls single swing gate installation: $850 to $1,400 parts and labor, depending on the arm model and whether power is already at the gate.
• New Ghost Controls dual swing gate installation: $1,400 to $2,200, since both arms must be synced and wired together.
• Ghost Controls actuator replacement (arm only, existing control board): $380 to $650 parts and labor.
• Ghost Controls control board replacement (R20 or equivalent): $300 to $520 parts and labor, including reprogramming remotes and keypads.
• Photo-eye realignment or replacement: $120 to $240 per set, including testing the safety reversal.

What moves the price: gate weight and length, whether the post is plumb, the distance from your electrical panel to the gate, and whether you want battery backup. We quote the whole job up front, so the number you approve is the number you pay. Call (850) 816-3017 for a free estimate on your specific gate.

Why Orlando Homeowners Call Portcullis Gate Repair Orlando for Ghost Controls Work

We are an independently owned Kingswell company, which means one thing that matters: the Kingswell Guarantee is written on every job we do, and it is the same standard across every Kingswell location. A written price before the work starts. A real arrival window. A clean job site when we leave. A written guarantee on the repair. And if the repair fails within 365 days, we come back and make it right at no charge. That is not a marketing line. It is printed on the invoice.

Our technicians are background-checked and arrive in uniform, so you know who is at your gate. And while Ghost Controls is a brand we know well, we service eight other major operator brands including LiftMaster, Mighty Mule, and DoorKing. If you have a mixed system or you are thinking about switching brands, we can give you straight advice instead of a sales pitch. Dean Prescott has been doing gate work across Orlando for the better part of two decades, from residential slide gates in Baldwin Park to commercial swing operators along the International Drive corridor. Tell me what the gate is doing, or not doing, and I’ll give you a real number before I touch a thing.

FAQs

Get a Written Price on Ghost Controls Gate Installation in Orlando

If your Ghost Controls gate is down, limping, or simply due for a proper installation, call (850) 816-3017. A live person answers, day or night. We will ask what the gate is doing, give you a real dollar range, and schedule a time that works. You get the written price before any work begins, and the Kingswell Guarantee on the work when we are done. That is how we have done it in Orlando since 2008.

Written by Dean Prescott, Owner, Portcullis Gate Repair Orlando, serving Orlando and nearby areas.