Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Orlando?
Most gate parts and welding work in Orlando runs between $180 and $850 for a typical repair call. Simple fixes like hinge replacements or bracket welding land on the lower end, around $180 to $350, while full actuator swaps (the motorized arm that pushes the gate open) or significant structural welding on heavy iron gates run $500 to $1,400. The fastest way to get an exact number is to call (850) 816-3017 and describe what you’re seeing – we’ll give you a written price before any work starts.
Here’s what our technicians in Orlando actually see on the job: heat, humidity, and afternoon thunderstorms take a real toll on gate hardware. Rust forms faster here than in drier climates, and that rust is the number one reason welded joints fail and hinges snap. But before you assume the worst, know this: most gate part failures are repairable in a single visit, and the price is almost always lower than a full gate replacement.
Gate Parts & Welding Cost Breakdown (2026)
The table below gives you real Orlando market ranges for the most common gate parts and welding jobs we do. These are the prices you should expect to see from a licensed, insured gate company in the Orlando metro area in 2026. They include parts and labor unless noted.
| Job Type | Typical Orlando Price Range | What’s Included |
|---|---|---|
| Hinge replacement (standard swing gate) | $180 – $320 | New hinges, removal of old hardware, alignment, lubrication |
| Weld repair: gate frame crack | $220 – $450 | On-site weld, grinding, primer and paint touch-up |
| Gate bracket or mount welding | $180 – $380 | Re-weld loose bracket, align gate, test operation |
| Actuator (gate opener arm) replacement | $500 – $1,400 | New actuator matched to existing operator, install, travel limits set |
| Gate wheel or roller replacement | $160 – $300 | New wheel assembly, track adjustment, lubrication |
| Slide gate track repair | $250 – $600 | Straighten or replace damaged track section, align gate |
| Ornamental iron repair (scrollwork, pickets) | $200 – $700 | Weld or replace damaged pickets, grind smooth, prime and paint |
| Full weld-on gate frame reinforcement | $350 – $850 | Steel plate or angle iron welded to weak frame points |
What moves a price up or down? The biggest variable is the gate’s material and weight. A lightweight aluminum driveway gate takes less labor to weld than a heavy wrought-iron or steel gate that requires two technicians to lift back into alignment. Access matters too: if the gate post is set in concrete that has shifted, the repair involves breaking out and re-setting the post, which pushes a simple hinge job toward the $500 range. And the gate operator brand on your property affects parts cost. A DoorKing or FAAC actuator runs more than a basic Mighty Mule arm, though the labor is similar.
Portcullis Gate Repair Orlando services all nine major gate operator brands we work with – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so we’re not guessing at your system’s wiring or mounting points. We already know the specific hardware on your gate before the truck pulls into the driveway.
What Affects Gate Parts & Welding Pricing in Orlando
Every gate is different, and Orlando’s climate and housing stock create pricing patterns you won’t find in other cities. These are the factors that move your quote up or down:
- Gate material and weight. Steel and wrought iron take longer to weld and require more grinding and prep than aluminum. A heavy iron gate in neighborhoods like Baldwin Park or College Park needs extra hands, and that labor is part of the price.
- Corrosion from Orlando humidity. Florida’s humidity plus rain means surface rust and pitted metal are common. Welders spend more time cleaning the weld area before striking an arc, which adds labor time to structural repairs.
- Operator brand and age. An older FAAC hydraulic actuator or a commercial Viking swing arm costs more to source parts for than a current-model Ghost Controls unit. Newer systems also tend to have plug-and-play wiring, while older units require more diagnosis.
- Gate construction and failure point. A cracked weld at the hinge is quick to access. A snapped gate frame near the bottom rail might require removing the gate entirely, welding on both sides, and re-hanging it – tripling the labor.
- Emergency service timing. A gate stuck open at 11 p.m. in Dr. Phillips or Lake Nona is a security problem, and we answer the phone 24/7. Same-day or after-hours dispatch is available without a markup on the parts themselves – you’ll see the price in writing before we touch the gate.
- Access and site conditions. Gates set in brick columns, gates surrounded by landscaping, or gates on narrow easements in Winter Park take longer to work around. None of this is a surprise fee – it’s just time on the job, and we price it upfront.
What Does Gate Welding Cost in Orlando per Hour?
Most Orlando gate companies bill welding and fabrication at between $95 and $150 per hour. At Portcullis Gate Repair Orlando, we don’t bill by the hour for most repairs. We quote a flat price for the job before we start. You’ll know the total number in writing, and that’s the number you pay – whether the weld takes forty minutes or two hours.
Common Gate Parts We Replace in Orlando
Here’s a quick vocabulary guide to the parts our technicians mention most often, because knowing the names helps you explain what’s wrong when you call:
- Actuator – the motorized arm that physically pushes or pulls the gate open. If your gate was working fine and now only opens halfway, the actuator is the first suspect.
- Hinges and pintles – the pivot points the gate swings on. Worn hinges make the gate sag and scrape the ground on the latch side.
- Wheels and rollers – found on slide gates and cantilever gates; these carry the gate’s weight along the track. A flat-spotted wheel makes a grinding sound.
- Track and guide brackets – the steel rail along the fence line. Orlando’s sandy soil shifts and can knock track sections out of alignment.
- Receiver and edge sensors – the safety eyes that stop the gate if a car or child is in the path. Corroded wiring in humid conditions causes false triggers.
- Gate frame and pickets – the structural metal of the gate itself. Cracked welds and rust-through are common on Orlando gates older than ten years.
How Much Does It Cost to Weld a Broken Gate Frame in Orlando?
A typical weld repair on a cracked gate frame in Orlando runs $220 to $450. The work involves grinding away rust and old paint at the crack, welding the joint solid, smoothing the bead, and priming and painting the repair so it doesn’t rust again in Florida’s humidity. If the crack has been ignored long enough that the frame has bent, the repair becomes a reinforcement job instead – we add steel plate or angle iron, which pushes the price into the $350 to $850 range.
We see this most often on older decorative gates in neighborhoods like Conway and Pine Hills, where iron gates from the 1990s and early 2000s are reaching the end of their original welds. Humidity gets under the powder coating, rust expands inside the joint, and the weld eventually fatigues. The repair is straightforward and permanent when the area is prepped properly.
Is It Cheaper to Weld a Gate or Replace It?
Almost always, welding is cheaper. A new residential gate in Orlando runs $1,500 to $6,000 or more depending on size, material, and whether you’re replacing the operator too. A weld repair, even a substantial one, usually stays under $850. The math changes when a gate has multiple rust-through failures in the frame – if we’re chasing four or five structural cracks, the labor adds up and a replacement starts looking like the better long-term buy. We’ll tell you honestly which side of that line your gate sits on, in writing, before any work starts.
How to Save on Gate Parts & Welding
Some savings come from timing, some from doing small things before a small problem becomes a big one. Here’s what works in Orlando:
- Call at the first symptom. A gate that’s scraping, squealing, or opening slower than it used to is sending a signal. A $180 hinge replacement caught early stays $180. Let it wear into the frame and you’re looking at a $600 structural repair.
- Replace the part, not the whole system. If the actuator failed but the control board, receiver, and safety edges are all working, you don’t need a whole new operator package. We quote parts-only repairs whenever possible.
- Ask for a written quote and compare it honestly. We give the price in writing before any work starts. If another quote is lower, read what’s included – some companies quote the part but not the labor to remove the old one, or the welding, or the return visit to re-align everything.
- Bundle maintenance during one visit. While the tech is on site for a weld repair, have the hinges, wheels, and operator checked at the same time. You’re paying for the trip once, and catching the next failure early saves real money.
- Use your guarantee. Every Portcullis Gate Repair Orlando job comes with the 365-Day Done Right Promise. If the repair fails inside that period, we come back and fix it at no charge – including the free return visit. You never pay twice for the same repair.
Portcullis Gate Repair Orlando offers free estimates. You can call (850) 816-3017, describe the problem, and get a realistic price range before we even schedule the truck. If you want an exact number, we’ll come out, look at the gate, and hand you a written quote – no obligation, no pressure.
The Kingswell Guarantee and What It Means for Orlando Homeowners
Portcullis Gate Repair is an independently owned Kingswell company. That means every job follows the Kingswell Way: we say the price before the work begins, we show up in the window we gave, we leave the job site cleaner than we found it, we put the guarantee in writing, and we come back if the repair fails. It’s not a franchise promise – it’s a written one, stamped on every invoice.
For Orlando homeowners, that written guarantee matters. A weld repair that fails two months later at a rental property in MetroWest or a family home in Hunter’s Creek doesn’t mean another bill. Under the 365-Day Done Right Promise, the return visit is free, and the correction is free. That’s the reason our customers call us when another gate company has already disappointed them.
Dean Prescott, who runs Portcullis Gate Repair Orlando, built the shop on a simple rule: if you wouldn’t put it in writing, don’t expect a customer to pay for it. That’s why the price is on paper before the first bolt comes off, and why the guarantee period is a full year, not thirty days.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Orlando?
Gate welding in Orlando runs $180 to $850 for most residential repairs, depending on the crack’s location, the gate’s material, and how much rust removal the weld area needs. Small bracket welds start near $180; structural frame reinforcement runs $350 to $850. Call (850) 816-3017 for a written quote on your specific gate – estimates are free.
Can you weld a gate on site, or does it need to go to a shop?
We weld on site in almost every case. Mobile welding equipment comes on the truck, and our technicians are set up for both stick and MIG welding in the field. The gate stays on its hinges or gets removed, repaired, and re-hung the same day. On-site welding in Orlando typically adds no extra charge – it’s how we work.
How much does a gate actuator cost in Orlando?
A replacement gate actuator (the motorized arm) runs $500 to $1,400 parts and labor in Orlando. The price moves with the brand: Mighty Mule and Ghost Controls arms sit on the lower end, FAAC and DoorKing units run mid-range, and commercial-grade Viking or BFT actuators cost more. We service all nine major brands and match the actuator to your existing operator so nothing else needs replacing.
How much does it cost to repair a sagging gate in Orlando?
A sagging gate typically costs $180 to $320 to fix when the cause is worn hinges, which is the most common culprit in Orlando. If the gate post itself has shifted in the sandy soil common in neighborhoods like Azalea Park or East Orlando, re-setting the post adds $200 to $450. Call us and we’ll tell you which problem you have and what the fix will cost, in writing, before we start.
Can you come today for an emergency gate repair?
Yes. Portcullis Gate Repair Orlando answers calls 24 hours a day, 7 days a week, including holidays, and we dispatch same-day in most of the Orlando metro area. A gate stuck open is a security issue, not a scheduling inconvenience. Call (850) 816-3017 and you’ll reach a live person, not a voicemail tree.
How much does it cost to replace a gate wheel or roller?
Replacing a slide gate wheel or roller in Orlando runs $160 to $300. The price includes the new wheel assembly, track alignment, and lubrication. If the track itself is bent or rusted through, the job becomes a track repair at $250 to $600. Most wheel replacements are quick – we finish the bulk of them in under two hours.
Is it cheaper to repair or replace a gate operator?
Repair is cheaper in about 70% of cases. A replacement control board runs $250 to $500, and a new actuator runs $500 to $1,400. A whole new operator package starts around $1,200 and climbs from there. We only recommend full replacement when the existing system has multiple failing components and patching it would leave you with a gate that works today and quits next month.
Is welding worth it on an old rusted gate?
For most Orlando gates, yes. The humidity here causes surface rust, which looks worse than it is. Once we grind to clean metal and weld the joint, the repaired area is often the strongest part of the gate. If the rust has eaten through multiple frame rails, replacement becomes the smarter buy – but we’ll show you the math on paper before you make that call.
For more on our shop and what we do across the Orlando area, start at our home page. If you want the full breakdown of the parts we stock, the welding processes we use on site, and the specific brands we service, see Gate Parts & Welding in Orlando. And if your gate is making a sound, dragging, or refusing to open, call (850) 816-3017 now – we’ll tell you the likely culprit and what the fix will cost, in plain numbers, before you hang up.
Pricing reflects the Orlando market as of 2026. Portcullis Gate Repair Orlando offers free estimates – call (850) 816-3017.
Written by Dean Prescott, Owner at Portcullis Gate Repair Orlando, serving Orlando since 2008.
What Our Customers Say
"Our driveway gate stopped halfway and wouldn't close, which is a problem when it's the only thing between the street and the yard. They came out same day, replaced the motor, and it's smooth again."
- Leonard Pace"Gate was dragging and screeching across the driveway. I figured I'd need a whole new setup. He adjusted the track and rollers and it was a fraction of what I expected. Honest work."
- Omar Haddad"Installed a new gate for us after the old wooden one rotted out. Clean work, showed up on time both days, and the written price didn't change. It swings perfectly."
- Donna Kirkpatrick